Teka Dishwasher Troubleshooting
Knocking noise within the water pipes, plastic items are discoloured and so on – the causes of any problem in the operation of the Teka dishwasher are presented in the tables below. The information in each of them is dedicated to Teka dishwasher troubleshooting. You could find a description of the problems (or fault codes), causes and possible solutions.
Teka DW7 56 FI Dishwasher Troubleshooting
Problem | Cause | Solution |
---|---|---|
Dishwasher doesn't start | Fuse blown, or the circuit breaker acted | Replace fuse or reset circuit breaker. Remove any other appliances sharing the same circuit with the dishwasher |
Power supply is not turned on | Make sure the dishwasher is turned on and the door is closed securely. | |
Make sure the power cord is property plugged into the wall socket. | ||
Water pressure is low | Check that the water supply is connected properly and the water is turned on. | |
Door of dishwasher not properly closed. | Make sure to dose the door properly and latch it. | |
water not pumped form dishwasher | Kink in drain hose | Check drain hose. |
Filter clogged | Check coarse the filter | |
Kitchen sink dogged | Check the kitchen sink to make sure it is draining well. | |
If the problem is the kitchen sink not draining .you may need a plumber rather than a serviceman for dishwashers. | ||
Suds in the tub | Improper detergent | Use only the special dishwasher detergent to avoid suds. If this occurs, open the dishwasher and let suds evaporate. Add 1 gallon of cold water to the tub. Close and latch the dishwasher, then Start the "soak" wash cycle to drain out the water. Repeat if necessary. |
Spilled rinse-aid | Always wipe up rinse-aid spills immediately. | |
Stained tub interior | Detergent with colourant was used | Make sure that the detergent is the one without colourant. |
White film on inside surface | Hard water minerals | To dean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves. Never use any other deaner than dishwasher detergent for the risk of foaming or suds. |
There are rust stains on cutlery | The affected items are not corrosion resistant. | |
The lid of the softer is loose | Check the lip .Ensure the fix is fine. | |
Knocking noise in the wash cabinet | A spray arm is knocking against an item in a basket | Interrupt the programme, and rearrange the items which are obstructing the spray arm. |
Rattling noise in the wash cabinet | Items of crockery are loose in the wash cabinet | Interrupt the programme. |
Knocking noise in the water pipes | This may be caused by on-site installation or the cross-section of the piping. | This has no influence on the dishwasher function, if in doubt, contact a suitably qualified plumber. |
The dishes are not clean | The dishes were not loaded correctly. | |
The programme was not powerful enough. | Select a more intensive programme. | |
Not enough detergent was dispensed. | Use more detergent, or change your detergent. Rearrange the items so that the spray can rotate freely. | |
Items are blocking the path of spray arms. | ||
The filter combination in the base of wash cabinet is not clean or is not correctly fitted. This may cause the spray arm jets to get blocked. | Clean and/or fit the filter combination correctly. Clean the spray arm jets. | |
Cloudiness on glassware | Combination of soft water and too much detergent. | Use less detergent if you have soft water and select a shortest cycle to wash the glassware and to get them clean. |
Black or gray marks on dishes | Aluminum utensils have rubbed against dishes. | Use a mild abrasive cleaner to eliminate those marks. |
Detergent left in dispenser cups | Dishes block detergent cups. | Re-loading the dishes properly. |
The dishes are not drying | Improper loading Too little rinse-aid | Load the dishwasher as suggested in the directions. |
Increase the amount of rinse-aid/refill the rinse-aid dispenser. | ||
Dishes are removed too soon | Do not empty your dishwasher immediately after washing. Open the door slightly so that the steam can escape. Begin unloading the dishwasher only once t he dishes are barely warm to the touch. Empty the low basket first. This prevents water from dropping off dishes in the upper basket. | |
Wrong program has been selected | In short program the washing temperature is lower. This also lowers cleaning performance. Choose a program with a long washing time. | |
Use of cutlery with a low-quality coating | Water drainage is more difficult with these items. Cutlery or dishes of this type are not suitable for washing in the dishwasher. |
Teka LX710 Dishwasher Troubleshooting
Problem | Cause |
---|---|
Appliance does not start up | • Fault with fuse in mains electricity supply. |
• Rug not inserted in wall socket. | |
• Appliance door not closed properly. | |
• Programme button has not been pressed. | |
• Water tap not turned on. | |
• Blocked strainer in water intake hose | |
Error displays on the State Indicator “ B "with it blinking all the time When the buzzer emits 1 short warning signal every 30 seconds | Have you checked whether: • the door is closed properly |
When the buzzer emits 4 short warning signal every 30 seconds. | Have you checked whether: • the drain hose is crimped or bent. |
• the drain hose is too high | |
When the buzzer emits 5 short warning signal every 30 seconds | • the water is turned on and the hose is connected properly; |
• the water supply to the house is on and has sufficient pressure; | |
• the water supply hose is crimped or bent; | |
• the filter for the water supply hose is clogged. | |
• the drain hose is too low | |
When the buzzer emits 2 or 6 short warning signals every 30 seconds | Contact the nearest authorized service center |
If you take all these checks and the dishwasher still does not function or your dish- washer have any other error display, you can power the dishwasher OFF, and wait a few minutes. You can power the dishwasher on, try it again, if the dishwasher still does not function and/or the problem persists, contact the nearest authorised service center and provide them with the following information: | |
• the nature of the problem. | |
• the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door | |
Lower spray arm rotates with difficulty | • Spray arm is blocked by small items or food remains |
Lid in detergent compartment cannot be closed | • Detergent compartment has been overfilled. |
• Mechanism is clogged with remnants of detergent | |
Indicator lamps do not extinguish after washing has finished | Kiain switch is still set to ON |
Remnants of detergent stuck inside dispenser | • Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added |
Water remains inside appliance after programme has ended | • Blockage or kind in drainage hose. |
• Pump is jammed. | |
• Filters are blocked. | |
• The programme is still running. Wait for the programme to end | |
Unusual amount of foam is creased | • Normal washing up liquid has been poured into the rinse-aid container. |
• Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle | |
Appliance stops suddenly while washing is taking place | • Cut off electricity supply to appliance. |
• Water supply has been interrupted | |
Knocking sound can be beared while washing is taking place | • A spray arm is knocking against the dishes inside the appliance |
Rattling sound can be beared while washing is taking place | • Crockery has not been stacked properly inside the appliance |
Knocking sound coming from inlet valves | • This is caused by the way the water pipes have been laid and it has no effect upon the way the appliance functions. There is no remedy for this |
Remnants of food are stuck to the dishes, cutlery,etc | • Dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, etc. |
• Too many items in the rack. | |
• Items in the rack were touching each other. | |
• Not enough detergent was added to dispenser. | |
• Selected wash programme was not intensive enough. | |
• Rotation of spray arm was obstructed by dishes, etc. | |
• Nozzles in spray arm are blakcked by remnants of food. | |
• Filters are blacked. | |
• Filters have been incorrectly fitted. | |
• Waste-water pump is jammed | |
Plastic items are discoloured | • Not enough detergent was added to dispenser. |
• Detergent has insuffcient bleaching properties. Use a detergent containing a chemical bleaching agent | |
White stains are left on crockery, glasses have a milky appearance | • Not enough detergent was added to dispenser compartment. |
• Amount of rinse-aid was set too low. | |
• Although water is quite hard, no salt has been put in appliance. | |
• Water softener was set too low. | |
• Lid on salt container is not screwed tight. | |
• If you used a phosphate-free detergent. try a detergent containing phosphates and compare results | |
Dishes,cultlery.etc.have not been dried | • Selected programme did not include drying function. |
• Amount of rinse-aid was set too low. | |
• Items were removed from dishwasher too soon | |
Glasses have a dull appearance | • Amount of rinse-aid was set too low |
Tea stains or traces of lipstick have not been completely removed | • Detergent does not have a sufficient bleaching effect. |
• Washing temperature was set too low | |
Traces of rust on cutlery | • Cutlery is not sufficiently rustproof. |
• Salt content in washing water is too high | |
Lid on salt container is not screwed tight | Too much salt was spilt while filling container |
Teka LP800S Dishwasher Troubleshooting
Problem | Cause |
---|---|
The Dishwasher Does Not Start | - the plug is pushed into the socket correctly: |
- the power is on in the house: | |
- the door is closed properly: | |
- the ON-OFF swith is on "ON': | |
- the water supply is turned on. | |
The Dishwasher Does Not Load Water | - the water is turned on and the hose is connected properly: |
- the water supply to the house on and has sufficient pressure: | |
- the water supply hose is crimped or bent; | |
- the filter for the water supply hose is dogged | |
The Dishes Are Not Clean | - the water is turned on and the hose is connected properly: |
- the water supply to the house on and has sufficient pressure: | |
- the water supply hose is crimped or bent: | |
- the filter for the water supply hose is dogged | |
The Dishwasher Does Not Drain | - the drain hose is crimped or bent |
Lime Deposits or a White Film Form on the Dishes | - the lid to the salt container is dosed properly; |
- the rinse aid dosage is correct |
Teka DW845S Dishwasher Troubleshooting
FAULT | DESCRIPTION |
---|---|
E1 | The anti-flooding system (where present) has been tripped. |
E2 | The water level limitation system has tripped. |
E3 | The appliance cannot heat the water. |
E4 | The temperature sensor is disconnected. |
E5 | The appliance cannot take in the water. |
E6 | The appliance cannot drain the water from the tank. |
E7 | The dishwasher cannot measure the precise water quantity that has been loaded. |
E8 | Problem on the water distribution system to the baskets. |
E9 | Water intake system malfunction |
Teka LP8835W Dishwasher Troubleshooting
Problem | Solutions |
---|---|
The dishwasher won’t start or turn on | — Check that the mains plug is inserted and switched on at the power point. |
— Check that the relevant fuse hasn’t blown. | |
— Ensure that the dishwasher isn’t over-loaded and the door is closed completely. | |
— Error code El indicates that the water pressure is low. Ensure that the water supply is on and fully open. | |
Water isn’t being drained from the dishwasher | — Check that the drain hose isn’t kinked . |
— Check that the filter isn’t clogged. Follow the filter cleaning process within this user manual. | |
— Check that your waste outlet isn’t clogged. | |
Residual soap suds in the dishwasher after a wash cycle | — Ensure that you are only using dishwasher detergents and the correct dosage. |
— Open the dishwasher and allow suds to evapourate. Then add 1 litre of cold water into the base of the dish- washer, close the door, select any wash cycle and allow the dishwasher to drain the water. Repeat if necessary. | |
Stained interior | — Avoid using detergents with colourants, as they can lead to staining. |
White film on internal dishwasher surface | — This can be caused where the water quality is poor and contains hard water minerals. To clean the interi- or, simply use a damp sponge with some dishwasher detergent. Never use harsh abrasives. |
There are rust stains on cutlery | — The cutlery may not be corrosion resistant and shouldn’t be used within the dishwasher. |
Banging or knocking noise within the dishwasher cabinet during cycle | — A spray arm is knocking against an item within a basket. Pause the dishwasher and re-arrange the items to ensure the spray arms are free to rotate. |
The dishess are not drying | — Ensure that the diswasher is loaded correctly. |
— Ensure that you have Rinse Aid loaded in the Rinse Aid dispenser and try adjusting the Rinse Aid Dispenser to a higher level. | |
— Remember to slightly open the dishwasher door at the completion of its cycle. | |
Knocking noise within the water pipes | — This has no influence on the dishwasher function and relates to the household plumbing. |
— Speak to a qualified plumber to discuss your options. |