Frigidaire dishwasher error code

Frigidaire dishwasher error code i10

Frigidaire dishwasher error code i10

The dishwasher is not filling properly.

Check the water supply system and make sure the shutoff tap is fully released.

Frigidaire dishwasher error code i20

Frigidaire dishwasher error code i20

This happens when there is a drain problem resulting from a faulty drain pump or clogged drain lines. Please, check the pump and hose for twists and clogs. If you are going to use the dishwasher in junction with a garbage disposer, remove the plug in the side of the garbage disposer (if you are installing a new one), and let in the drain water. Sometimes the i20 error code denotes a draining issue (typical of this type of dishwashers).

If there is no drain water in the base, and the code is still there, it is because the pressure switch is activated as if the water was still there.

Unplug the dishwasher, remove the right-hand panel and the lower one on the front. The pressure switch will be in the bottom left corner. You can recognize it by a rounded shape and a thin hose leading to it.

Remove the hose and blow into it as hard as you can to eliminate whatever there is in the pressure chamber that could have blocked the flow.

Pull the hose back on the pressure switch and restart the machine.

Frigidaire dishwasher error code i30

Frigidaire dishwasher error code i30

There is a leak and/or overfill in the bottom section.

Check the inlet valve and be sure that all connections are tight. The dishwasher should be leveled properly.

Frigidaire dishwasher error code i50

Frigidaire dishwasher error code i50

There is a drain or wash motor problem.

Reset the unit. To do so, press Cancel or flip the circuit breaker for a few minutes. Then restart the machine. Most likely, the error will disappear.

Frigidaire dishwasher error code i60

Frigidaire dishwasher error code i60

Reset the unit by pressing Cancel or flipping the circuit breaker for a few minutes. Then restart the machine. Most likely, the error will be cleared.

Frigidaire dishwasher error code iC0

Frigidaire dishwasher error code iC0

There is an issue in the electronic control system.

Reset the dishwasher by pressing Cancel or flipping the circuit breaker for a few minutes. Then restart the unit. Most likely, the error will be cleared.

Frigidaire dishwasher error code UF

Frigidaire dishwasher error code UF

The fan is not working.

If you have launched the drying cycle and the fan is not spinning, most likely, the Main Control Board is not getting the signal proving that the fan motor is rotating at an appropriate speed. Make sure the wiring between the system and the Main Control Board is ok. If the wiring is good, replace the fan system. If the error continues, replace the Main Control Board.

Frigidaire dishwasher error code ER

Frigidaire dishwasher error code ER

Membrane Switch Failure

It often happens when the Main Control Board detects a stuck key, or a key is pressed too hard and/or several times. Make sure the wiring between the keypad and the Main Control Board is ok. If it is, but the error is still there, replace the keypad. If the keypad is good too, but the error is not going away, replace the Main Control Board.

Frigidaire dishwasher error code CE

Frigidaire dishwasher error code CE

Configuration Error

Make sure that the wiring between the keypad and the Main Control Board is ok. Be sure that all parts are installed correctly. If not, take steps to reconfigure the system. If necessary, use professional help.

Frigidaire dishwasher error code CL

Frigidaire dishwasher error code CL

Door Switch Not Closing

The Main Control Board is not getting a signal of the door closed. Check the door switches and the wiring between them and the Main Control Board. If everything is ok, replace the Main Control Board.

Frigidaire dishwasher error code dP

Frigidaire dishwasher error code dP

Drain Pump Issue

This error is shown in relay test when the drain pump is launched.

Frigidaire dishwasher error code FL

Frigidaire dishwasher error code FL

The Water Valve Is Open

This error is shown in relay test when the water valve is activated.

Frigidaire dishwasher error code HO

Frigidaire dishwasher error code HO

Heat Delay

This error appears when the control board delays a cycle until the water temperature reaches the set level to ensure correct performance.

Frigidaire dishwasher error code hs

Frigidaire dishwasher error code hs

Hall Sensor

The control board has received a signal from the hall sensor in the motor. Make sure that the wiring between motor and Main Control Board is ok. If it is, but the error is still there, replace motor. If this does not work either, replace Main Control Board.

Frigidaire dishwasher error code LO

Frigidaire dishwasher error code LO

Low Rinse Aid

There is not enough rinse agent in the water. Check the rinse aid dispenser and refill it.

Frigidaire dishwasher error code PF

Frigidaire dishwasher error code PF

Power Failure

There is a more than 10% power failure. Check the house wiring and use professional help, if necessary.

Frigidaire dishwasher error code rA

Frigidaire dishwasher error code rA

Rinse Aid

There is an issue with the rinse aid reed switch in the rinse aid dispenser. Make sure it is filled properly and refill it, if needed. If the error is still there, check the connection between the dispenser and the Main Control Board. If the error does not clear, replace the dispenser system. If this one does not work either, replace the Mani Control Board.

Frigidaire dishwasher error code RE

Frigidaire dishwasher error code RE

Rinse aid reed switch error

The rinse aid reed switch in dispenser is not opening.

Frigidaire dishwasher error code RF

Frigidaire dishwasher error code RF

Rinse aid error

This error occurs when the rinse aid reed switch in the dispenser is open. Try refilling the dispenser. If needed, replace dispenser assembly.

Frigidaire dishwasher error code rt

Frigidaire dishwasher error code rt

Relay / Triac Test

The relay test mode is on.

Frigidaire dishwasher error code Sd

Frigidaire dishwasher error code Sd

Detergent Dispenser

This error appears in the relay test mode when the detergent dispenser is functioning.

Frigidaire dishwasher error code tu

Frigidaire dishwasher error code tu

Turbidity Sensor

This error code appears with the turbidity sensor fails. This may be due to a wiring problem, so check the harness between the sensor and the main control board. If the wiring is ok, there is a problem either in the sensor of the Main Control Board. Check these components one by one and replace the faulty one.

Frigidaire dishwasher error code uo

Frigidaire dishwasher error code uo

This code stands for ‘vent open’: it refers to the vent with a fan on the upper back right corner of the tub, which pumps air through the unit to dry the dishes. The system will not start with the vent open. If you see this code on the display, check the wiring. If no issues are found, check the vent assembly and repair/replace faulty parts. If the assembly is ok, check the main control board and replace it if necessary.