Electrolux dishwasher error code

Electrolux dishwasher error code iF0

Electrolux dishwasher error code if0

Code iF0 (14 flashes) – an error was detected when filling the tub with water.

Possible cause: water filling takes longer than usual.

Troubleshooting: waste water needs to be drained, and a new filling has to be launched.

Electrolux dishwasher error code 1

Electrolux dishwasher error code 1

This code indicates a drain problem resulting in backed up water filling the system. Check the drain and make sure it is not clogged. If you are using in in conjunction with a garbage disposer, disconnect the drain from the disposer and connect it directly to the drain line. Remove the backed up water from the system and reconnect the pipe with the disposer. Launch the garbage disposer and make sure that none of your sinks is blocked.

Also, if you see indications flashing and the error code is there, you can try this: press Favorite and heavy simultaneously for about 10 seconds (until it stops flashing). The 08 code may show up. Then press Start. The machine should run properly. If it does not, seek professional help.

Electrolux dishwasher error code i10

Electrolux dishwasher error code i10

Code i10 (1 blink) – an error was detected with the intake of water within the specified period of time.

Possible causes:

  • valve, filter or hose is clogged in the water inlet system;
  • water supply is blocked.

Troubleshooting:

  • check if there is water in the house;
  • check the operability of the inlet valve;
  • inlet mesh filter needs to be checked and cleaned;
  • The filler hose needs to be inspected for clogging.

Electrolux dishwasher error code i20

Electrolux dishwasher error code i20

Code i20 (2 flashes) – an error was detected with the drainage of waste water.

Possible causes:

  • the drain filter, pump, or hose is clogged;
  • the drain pump stopped operating;
  • the hose for draining water is kinked;
  • the pressure switch did not switch on within the specified period of time.

Troubleshooting:

  • the filter and hose need to be cleaned of dirt;
  • the impeller of the pump is inspected for sludge, food debris or fragments of dishes in it;
  • the position of the drain hose need to be corrected;
  • check the pressure switch. Replace it if necessary.

Electrolux dishwasher error code 30

Electrolux dishwasher error code 30

This error code means that you have a leak in the system, which has resulted in the accumulation of water win the base section. When it happens, an anti-flood switch is activated, and it keeps the drain pump running in an effort to drain the water. This won’t let the machine work properly.

To clear the error, unplug the dishwasher. Drain it by tipping it backwards. Plug it back in and restart it to check if the error has gone. Usually, it does, because the anti-flood switch is deactivated when there is no water.

Electrolux dishwasher error code ib0

Electrolux dishwasher error code ib0

Code ib0 (11 flashes) – an error was detected in the operation of the water transparency sensor, which monitors water with the help of a light beam.

Possible causes:

  • mud scaling on the sensor;
  • float switch failure;
  • clogged drain system.

Troubleshooting:

  • the sensor needs to be cleaned of dirt;
  • perform the works described for code i20 (2 flashes);
  • in some cases, the sensor needs to be replaced.

Electrolux dishwasher error code id0

Electrolux dishwasher error code id0

Code id0 (13 flashes) – an error was detected in the operation of the tachometer, which controls and regulates the speed of the motor rotor.

Possible causes:

  • the fastening loosened due to vibration;
  • no grounding;
  • Sometimes the sensor windings may burn.

Troubleshooting:

  • check the resistance of the contacts which should change when the armature of the motor rotates;
  • check the sensor mount;
  • in exceptional cases, the Hall-effect sensor needs to be replaced.

Electrolux dishwasher error code 50

Electrolux dishwasher error code 50

This code signals a motor circuit issue. There may be a problem in the control board, which is located at the bottom, right behind the motor. It takes professional help to check the control board functions.

Electrolux dishwasher error code i60

Electrolux dishwasher error code i60

Code i60 (6 flashes) – an error was detected in the operation of the water heater.

Possible causes:

  • the heater or supply wires have burnt;
  • thermostat failure;
  • insufficient water in the tub;
  • failure of the circulation pump;
  • failure of the control module.

Troubleshooting:

  • check the condition of the wiring and the heater. Replace burnt wires and heater;
  • check the thermostat;
  • check the operation of the circulation pump. In case of a serious breakdown, the pump needs to be replaced;
  • check the operation of the control module.

Electrolux dishwasher error code i70

Electrolux dishwasher error code i70

Code i70 (7 flashes) – an error was detected in the operation of the thermistor. The heater does not function – it does not heat the water.

Possible cause: contacts have damaged due to a short circuit.

Troubleshooting: replace thermistor.

Electrolux dishwasher error code i80

Electrolux dishwasher error code i80

Code i80 (8 flashes) – an error was detected in the operation of EEPROM memory of the control module.

Possible causes:

  • flashing of the firmware;
  • the control module has failed.

Troubleshooting: replacement and firmware update of the control module.

Electrolux dishwasher error code i90

Electrolux dishwasher error code i90

Code i90 (9 flashes) – an error was detected in the operation of the control board. The program cannot be set.

Possible causes: flashing of the firmware.

Troubleshooting: replacement of the control board.

Electrolux dishwasher error code iA0

Electrolux dishwasher error code iA0

Code iA0 (10 flashes) – an error was detected in the operation of the water spraying system.

Possible causes:

  • the spray arm does not rotate;
  • the dishes are placed wrong.

Troubleshooting:

  • place the dishes in the rack correctly;
  • detect and eliminate the cause of the spray arm blockage.

Electrolux dishwasher error code iC0

Electrolux dishwasher error code iC0

iC0 code (12 flashes) – the loss of communication between the control panel and the control board.

Possible causes: control board failure.

Troubleshooting: call a service center specialist to replace the control board.

In general, any user can eliminate Electrolux dishwasher errors if they carefully study the description of the codes. To make the machine serve for a long time, you need to follow simple rules: do not put extremely dirty dishes in the tub and remove any clogging in a timely manner.