Aeg dishwasher error code
Aeg dishwasher error code i10
No water in the tub. Waiting time exceeded.
- Issues with the water level sensor.
- The inlet hose is clogged or kinked.
- The inlet tap is shut, there is no water in the water supply system.
- The intake valve is broken.
How to fix the problem:
- The part needs to be inspected. If it is faulty, it must be replaced.
- Inspect the inlet hose, remove the clog.
- Check if there is water in the water supply system.
- Check the intake valve. Replace if necessary.
Aeg dishwasher error code i20
No water drain.
- Drain system is clogged.
- Replace the drain hose.
- Issues with water level sensor.
- Breakdown of the drain pump.
How to fix the problem:
- Check the drain hose for clogging and kinking.
- Inspect the level sensor; replace it with a new part in case of malfunction.
- Inspect and clean the drain pump from debris. If the pump is faulty, replace it.
Aeg dishwasher error code i30
All dishwashers have a tray or water container in the base, which should catch water when there is a leak. It may get filled with water if the drain pipe gets clogged. If you have used your dishwasher as a waste disposer, you may also end up with water in the base.
There is an anti-flood float, which prevents overflow and activates the drain pump when water reaches a critical level. If you see the error code on the display, check the tray/container. If there is water in it, disconnect the unit from the mains (safety first!) and remove the water. When the float falls back to its proper position, the machine will operate properly.
However, if the problem reoccurs, steps must be taken to eliminate the cause. This may be a clog or faulty pump, or an item may have gotten into the system and pulled up the float. Please, check the base and the system for such issues. In some cases, parts need a repair or replacement.
Aeg dishwasher error code i50
This error code indicates a problem in the wash motor circuit. If it occurs too frequently, it may be due to a faulty motor or, more likely, the motor control board not working properly.
These dishwashers feature motors with separate control boards, and the latter are more likely to fail. To clear the error, check the motor for faulty parts, then the control board’s circuit lines. They could have grown rusty, or there is a short circuit. Not unlikely, you will need to replace the motor control board or part of it.
Aeg dishwasher error code i60
What the code means: the water does not heat up or overheats.
- The heating element has burnt.
- Water level sensor has failed.
- Pump malfunction.
- There were issues with the thermistor.
- Dishwasher control module is out of service.
What can be done if this code occurs:
- Check and replace the heater.
- Inspect the level sensor, its connections. Install new part in case of breakage.
- If there were problems with the installation of the machine or pump, the water is continuously draining, so the heating does not occur.
- You need to check the connection system, as well as the state of the pump.
Aeg dishwasher error code i70
Issues with wiring, NTC short circuit. Check and replace wiring. Inspect NTC sensor.
Aeg dishwasher error code i80 and i90
Problems with EEPROM communication or with the module firmware. Control module malfunction. Diagnostics and repair or complete replacement of the module.
Aeg dishwasher error code iA0
Spray arm does not function. You need to check and unblock the sprinkler.
Aeg dishwasher error code i0
There are problems with the transparency sensor.
- The transparency sensor does not work.
- Dishwasher cleaning is required.
How to fix the problem:
- Check and replace the transparency sensor.
- Clean the dishwasher.
Aeg dishwasher error code iC0
No communication with user interface. Control module fault. System crash. Dishwasher requires reboot. If the error is still there, the module needs to be diagnosed and repaired.
Aeg dishwasher error code iAd0
No signal from Hall-effect sensor.
- No water heating.
- Uncontrolled speed of motor.
Hall-effect sensor requires inspection and repair.
Aeg dishwasher error code iF0
No water intake. Low pressure in the water supply system. You need to wait for normal water supply pressure.